Where the energy really goes in a spa
When the consumption of an indoor spa is analysed, the split usually comes as a surprise. Intuition suggests the greatest expense is heating the water; the reality is that treating the air competes on equal terms with heating the water, and in installations with a large open water surface it often overtakes it.
The four principal sources, ordered by their usual weight, are as follows:
- Air treatment: dehumidification, heating of the space and fresh air. It runs many hours and often continuously.
- Hot water production for domestic use and for the pools: replacing the heat lost through evaporation, through fresh water and through conduction.
- Heat cabins: saunas, hammams and tepidariums, with consumption closely tied to the heating schedule.
- Pumping and filtration: smaller per unit, but running almost without stopping.
Why dehumidification weighs so much
Every litre of water that evaporates from a pool takes heat with it and has to be replaced; on top of that, the vapour has to be taken out of the air so it does not condense on the building fabric. The cost is paid twice: in reheating the pool and in the work the dehumidifier does.
Which is why the open water surface, the water temperature and the movement at the surface — waterfalls, jets, air beds — are not only experience decisions: they are energy decisions. A heavily aerated hydrotherapy pool consumes appreciably more than a still one of the same area, and it is worth knowing that when the programme is defined, not when the first bill arrives.
How to reduce the consumption of the hot water pool
These are the measures with the best ratio between cost and impact:
- Cover the pools outside opening hours. It is the most effective measure and the least costly. A cover stops night-time evaporation almost entirely.
- Set the temperature with judgement. Every additional degree in a large pool shows up throughout the year.
- Control the movement at the surface. Programme the air features and waterfalls on demand, not running permanently.
- Insulate the pool and the pipework properly. It is done once and works for the whole life of the installation.
Heat recovery: what it is and when it pays
A dehumidifier extracts moisture and, in doing so, releases heat. Recovering it to warm the air of the room or to preheat the pool water makes use of energy that would otherwise go to waste. In installations that run many hours a year, it is one of the investments that justify themselves most easily.
It is less worthwhile in spas with a markedly seasonal opening and few hours of use, where the additional cost of the equipment takes too long to pay back. As with almost everything here, the answer depends on the actual operating regime, which is why it is calculated at the engineering stage with the hotel's data and not with assumptions.
The efficiency of a spa is not bought with equipment: it is decided in the design and preserved through maintenance.
Saunas and hammams: real consumption versus perceived consumption
A sauna left on appears to consume a great deal and usually sits below what is assumed: the expense is not in keeping it hot, but in heating it from cold several times a day. In installations with irregular use, defining the heating schedule properly — time slots, holding temperature, switch-off on inactivity — can have more impact than changing the heater.
The hammam is different: the steam generator consumes water and energy continuously while in service, and its performance drops noticeably if water quality causes scaling. Here, water treatment and energy consumption are the same problem.
Which measures pay off in the first year
- Pool covers and a night-time closing protocol.
- Reviewing and adjusting the temperature and humidity set points, which are often inherited from commissioning and have not been touched since.
- Time programming of the cabins and air features.
- Zoning so that whole areas can be shut down in low season.
- Maintenance of the heat exchange: cleaning the coils, descaling and controlling water quality.
These are measures of operation and adjustment rather than building work, so they can be applied to an installation already in service. They form part of the audit of an existing installation.
When investing in efficiency does not pay
If the installation has an underlying problem — badly sized dehumidification, no insulation, inadequate water treatment — adding more efficient equipment on top only makes the problem consume slightly less. Before investing in efficiency you have to correct what is wrong, and that sometimes means accepting that what is needed is a refurbishment and not an improvement.
Is your spa consuming more than it should?
We audit the installation, review consumption and set points, and tell you what can be corrected by adjustment and what requires intervention. With figures, not impressions.
Make an enquiry



